2007 honda pilot 3.5 2 wheel drive serpentine belt diagram - 2007 Honda Pilot (2024)

FAQs

How do you find a serpentine belt routing diagram? ›

A: Commonly a belt routing diagram sticker is on the underside of the hood or in the engine compartment. If there is no diagram, make a sketch of the belt and pulleys before removing the belt. This will help you re-route the new belt correctly.

The average cost for a Honda Pilot Serpentine Belt Replacement is between $102 and $123. Labor costs are estimated between $48 and $60 while parts are priced between $55 and $63.

Slide a breaker bar or half inch drive ratchet into the hole in the center of the new tensioner pulley and turn it clockwise to lower it as you slip the drive belt over the tensioner pulley last. The new tensioner should hold the belt at the proper level of tension once you release it.

Are Serpentine Belts Directional? Because nearly all serpentine belts are symmetrical, a new belt's direction of rotation usually doesn't matter. What does matter, though, is that the new belt is routed correctly around the pulleys. It's also important that the grooved side of the belt faces toward the pulley grooves.

EXAMPLE: 6PK1003 » 6 - This indicates the number of ribs on the belt; therefore, this is a 6-rib belt. » PK – The “P” indicates a metric designation, and the “K” indicates the belt is automotive per SAE J1459. » 1003 - This is the effective length of the belt expressed in millimeters.

To check the alignment of the belt, place a straight edge or laser alignment tool across the face of the pulleys, making sure it touches both pulleys. Then, move the straight edge or laser to the side of the belt and check for any gaps between the belt and the straight edge or laser.

Plus, replacement is relatively easy, and if you're wondering how long does serpentine belt service take, it's less than an hour for most vehicles.

The average cost for serpentine belt replacement is between $109 and $134. Labor costs are estimated between $57 and $72, while parts range between $52 and $62. Whether you go to the mechanic or do it yourself, replacing a serpentine belt costs $58 to $126.

Serpentine belts are built tough, and due to advancements in rubber technology, they typically last about 100,000kms or 5 years before you'll need to replace them.

Misalignment pulleys or tensioner: If the belt is not properly aligned on the pulleys, it can wear unevenly or slip off entirely, leading to its premature failure. This situation usually happens if some of the components have been previously removed, replaced, and not returned in to place properly.

How much tension should a serpentine belt have? ›

Use a ruler to check the belt's tension.

Instead, use a ruler to measure the distance between the two furthest pulleys and find the midway point. Pinch that point between your index finger and thumb and move it back and forth. The belt should have about a half an inch of play when at the appropriate tightness.

The way to remove tension will be to pivot the tensioner using a tool (1) on the nut of the tensioner pulley, or (2) a special tool-lug outcropping from the tensioner or (3) in a square opening in the bracket of the tensioner pulley, cover or cap that protects the spring.

You can find the correct size of serpentine belt for your car in the owner's manual or by using an online belt sizing tool. If you are unsure about the size of the serpentine belt you need, it is best to consult a mechanic or an auto parts store.

The squealing sound is most likely due to the belt slipping or a misaligned pulley. The noise is an indication that the belt needs to be replaced as soon as possible. Sometimes the squealing will start as a very light sound, but over time the squealing will get worse until the belt finally fails.

Note the placement of belt

To preserve the belt's position, take a few snapshots from different angles or sketch the way it winds through the engine. If the belt is already out of place, locate the driver's manual or the under-the-hood placard, where you'll find a sketch of the routing.

Most vehicles nowadays usually have a belt routing sticker located somewhere in the engine compartment, making it even easier.

How To Identify a V-Belt Pulley. The easiest way to identify a V-belt pulley is by finding the part number or identification components on the pulley itself. Different brands, as well as different pulley types, have various ways they may display these numbers.